RPM = (SFM x 12) / (pi x diameter), which shop charts shorten to RPM = 3.82 x SFM / diameter in inches. A 1 inch 1018 steel bar turned with HSS at 100 SFM runs at about 382 RPM; the same bar in 6061 aluminum at 250 SFM runs at about 955 RPM.
D is the diameter that is cutting: the workpiece diameter on a lathe, the cutter diameter on a mill or drill press. The surface speeds are conservative starting points for hobby machines; raise them when the finish and the chips tell you the setup can take it.
Tools that match your numbers
Lathes whose listed speed range covers your RPM
Grizzly sells these lathes factory-direct. Each is shown only if its own listed spindle range includes the speed you just calculated.
Nothing we carry is listed for that number. Change a value above, or compare the wider range below.
- Smaller option, below your numberGrizzly G4000 9 x 19 Benchtop Metal LatheFactory-direct from Grizzly
Your target is about 382 RPM at 1 in. Its listed spindle range, 130 to 2,000 RPM, covers that (8-3/4 in listed swing over the bed).
Listing: Swing over bed 8-3/4 in, spindle speeds 130 to 2000 RPM, 6 speeds.
Buy direct at Grizzly - Smaller option, below your numberGrizzly G9972Z 11 x 26 Benchtop Metal LatheFactory-direct from Grizzly
Your target is about 382 RPM at 1 in. Its listed spindle range, 150 to 2,400 RPM, covers that (10-1/2 in listed swing over the bed).
Listing: Swing over bed 10-1/2 in, 26 in between centers, 6 speeds from 150 to 2400 RPM.
Buy direct at Grizzly - Smaller option, below your numberGrizzly G8688 7 x 12 Mini Metal LatheFactory-direct from Grizzly
Listing: Swing over bed 7 in, variable spindle speed 100 to 2500 RPM.
Buy direct at Grizzly
If that diameter is a mill or drill cutter
Matched on cutter material, size and (where the listing says so) the metal family, using the sizes printed in each listing.
Nothing we carry is listed for that number. Change a value above, or compare the wider range below.
- Smaller option, below your numberAUTOTOOLHOME 8PCS HSS 4-Flute End Mill Set CNC Milling Bits 1/16''-1/2''Under $25Check price on Amazon
- Smaller option, below your numberShars 3/16" - 3/4" 4 Flute HSS Uncoated Single End Center Cut End...Under $100Check price on Amazon
- Smaller option, below your numberVCT Tools 20 Pc Hss Tin Coated End Mill SetUnder $100Check price on Amazon
- Smaller option, below your number6Pcs 1/8" - 1/2" 4 Flute Solid Carbide Square End Mill Set - AlTiN...Under $100Check price on Amazon
- Smaller option, below your numberBestParts 1/4" 3 Flute Solid Carbide Long End Mill for AluminumUnder $25Check price on Amazon
- Smaller option, below your number2Pcs 5/16in 37°Helix Solid Carbide Square End Mill for AluminumUnder $100Check price on Amazon
- Smaller option, below your number3/8" 3 Flute Carbide Square End Mill for AluminumUnder $50Check price on Amazon
- Smaller option, below your number1/8" Carbide Square End Mill for Aluminum Copper ApplicationsUnder $50Check price on Amazon
- Smaller option, below your numberHunricho 2PCS 1/2'' Carbide Square End Mill Bits SetUnder $100Check price on Amazon
Eye protection to go with it
Glasses whose listing states ANSI Z87.1. Check the markings on the lens and frame and follow the maker's instructions; this is not a safety guarantee.
Nothing we carry is listed for that number. Change a value above, or compare the wider range below.
- Smaller option, below your numberTICONN 1PK Anti-Fog Safety Glasses for Men & WomenUnder $25
Eye protection for the machine that runs these numbers. The listing states ANSI Z87.1; check the markings on the lens and frame and follow the maker's instructions.
Check price on Amazon - Smaller option, below your numberErgodyne Skullerz SIXTEN Safety Glasses with Side ShieldsUnder $25
Eye protection for the machine that runs these numbers. The listing states ANSI Z87.1; check the markings on the lens and frame and follow the maker's instructions.
Check price on Amazon
Tools for this job
The tooling this calculation is usually for, spread across the price range.
How does the rpm calculator work?
Surface speed is how fast the metal moves past the cutting edge, in feet per minute. Every tool and material pair has a speed range where the edge cuts cleanly without overheating. Spindle RPM is just the way you dial that speed in, and it depends on diameter: the same RPM moves the rim of a 3 inch bar three times faster than a 1 inch bar.
That is why RPM must drop as diameter grows, and why a facing cut speeds up at the edge and slows at the center. On a hobby lathe with a belt or a variable speed dial, pick the nearest speed at or below the figure here.
Frequently asked questions
What does 3.82 mean in the RPM formula?
It is 12 divided by pi, rounded. Surface speed is in feet per minute while diameter is in inches, so you multiply by 12 to convert feet to inches and divide by pi times the diameter to get revolutions. RPM = 3.82 x SFM / D gives the same answer as the long form to within about a tenth of a percent, which is far more precise than any starting speed chart.
Should I use the workpiece or the tool diameter?
Use whichever one is spinning and cutting. On a lathe the work spins, so use the diameter of the workpiece where the tool is cutting. On a mill or a drill press the cutter spins, so use the end mill or drill diameter. For boring on a lathe, use the bore diameter being cut.
What if my lathe cannot reach the calculated RPM?
Run at your top speed. The only consequence of running slower than ideal is a lower surface speed, which means a slower job and sometimes a slightly worse finish in aluminum. Running faster than ideal is what burns tool edges, so being speed limited on a small machine is safe.
Keep going
Formulas are standard shop math; starting speeds are conservative conventions for hobby machines. Not professional engineering advice. Wear eye protection and keep hands, gloves and sleeves clear of rotating work.


